Arduino Stack Exchange
Arduino Stack Exchange

Most Popular

more tags
1500 questions
5
votes
3 answers

Is it possible to create a standalone exe which can burn the code into a Teensy 3.1?

So here's the scenario. I have sent my teensy 3.1 circuit to a client of mine And now I need to update the code burned onto teensy without providing client access to the code So is it possible to create an exe or an installer of a kind which on…
newbie2015
  • 223
  • 2
  • 9
5
votes
1 answer

How do I convert code between Arduino platforms?

What documentation is available regarding the differences between the different Arduino platforms? For example, I have some code written for an Arduino Teensy that I would like to run on an Arduino Mega. Is there documentation on the capabilities…
Mark Harrison
  • 559
  • 3
  • 14
  • 23
5
votes
4 answers

How to connect more than 10 sensors to Arduino uno r3

How I can connect more than 10 sensors to Arduino Uno R3? I calculated it and I can connect just 4 fire flame sensors (sensors which can find a fire (a candle, for example)) and maybe 1 ultrasonic sensor. I need more for my project. I need an IR…
Mr. Robot
  • 151
  • 1
  • 1
  • 4
5
votes
4 answers

Is there any way I can turn off the 5V pin?

I'm trying to find a way I can toggle the 5V pin to turn on/off. I want the voltage to pass to another wire at a certain point. It should be off and then when something happens, the 5V should turn on. How can I do this?
ninesalt
  • 159
  • 1
  • 1
  • 2
5
votes
2 answers

Trouble with Timer 0

I'm taking my first wobbly steps outside the Arduino IDE and I'm not having much success with timers / interrupts. I can set a pin to output and light an LED with registers fine but I cannot for the life of me get it to blink using a timer. I have…
Ashlyn Black
  • 339
  • 1
  • 9
5
votes
2 answers

I²C with ATTiny85 at 8MHz using TinyWireM library

Hello fellow Arduino enthusiasts, I am trying to make the ATTiny85 talk I²C with a MMA7660 breakout board I have (it's an accelerometer, this is a follow up question to my previous one). I would state in advance that the I²C chip works perfectly…
Omer
  • 1,390
  • 1
  • 9
  • 15
5
votes
2 answers

Arduino power sources

Is it safe to connect a USB input to an Arduino (Nano) at the same time as an external regulated 5V supply to its 5V pin is connected, assuming the supplies have common grounds ? Will (I hope) the external 5V be used so as to not draw too much…
Robert Murphy
  • 51
  • 3
5
votes
2 answers

Read RC receiver channels using Interrupt instead of PulseIn

I am designing my own quadcopter control algorithm, whereby I currently read 4 RC receiver channels using PulseIn on each loop in the following manner: ch1_raw = pulseIn(rcPin1, HIGH, 25000); In other words, ch1_raw contains the length of a HIGH…
RLJ
  • 53
  • 1
  • 4
5
votes
1 answer

How to confirm a pin is fried

How do you confirm a pin has been damaged and is unable to work as a digital input? I tried detecting a pushbutton (connecting ground to pin 11 with a pullup resistor enabled) on a fresh Arduino Uno and digitalRead() always registers 0, regardless…
Cerin
  • 1,688
  • 2
  • 28
  • 44
5
votes
1 answer

HDMI EDID emulator

I am working on a project where i emulate the EDID of a screen to force a source into sending data on a certain resolution. I read the original EDID code of a screen and change the timings into the resolution I want to force the source in, i send…
CedricGr
  • 51
  • 2
5
votes
6 answers

LCD 16*02 I2C shield only shows first character printed

I have an I2C LCD screen provided with a Sunfounder kit and certainly built by DFRobot or such a constructor (there is nothing written on the LCD), and an Arduino Uno R3 copy. My issue is when I use lcd.print() to write a string on the LCD, only the…
AFract
  • 193
  • 1
  • 3
  • 15
5
votes
2 answers

One workspace, two IDEs - Possible?

How can I create a workspace & projects so that either the Arduino IDE or the EclipseArduino IDE may be used to develop the project, interchangeably? I have both IDEs installed and working but in separate workspaces. I need: One workspace that…
JRobert
  • 15,397
  • 3
  • 24
  • 51
5
votes
3 answers

How do I create a 9 bit number based on values from 9 digital inputs?

I have 9 pins that are inputs from 9 IR LEDs. I want to combine all their results into one 9 bit number. example: pin1 = high, pin2 = high, pin3 = high, pin4 = low, pin5 = high, pin6 = low, pin7 = low, pin8 = high, pin9 = low 9 bit number =…
user3216081
  • 51
  • 1
5
votes
1 answer

Modbus Communication protocol for Arduino as Slave

I have an Arduino Uno board, with these components: rs-485 Modbus module shield Multiprotocol radio shield board for Arduino In addition I have a level sensor which reads either 1 when it is above water, and 0 when it is below. I need to be able…
lshas
  • 151
  • 5
5
votes
1 answer

ESP 8266 does not respond at all

I have a ESP8266_01, and I wired up. It does not work for me. I have connected the ESP to an Arduino Uno. I am using a 5V pin from uP with a 3.3V regulator, and I have a voltage divider between RX(ESP) and TX(uP). And I am sure that the wiring is…
Chen
  • 53
  • 1
  • 1
  • 3
1 2 3
…
99 100